Disabling SIP-ALG in your Router or Firewall

Disabling SIP-ALG in your Router or Firewall

Disabling SIP-ALG is an essential part of configuring the firewall on your router and optimizing it for Exitty service. Many ALGs (including Cisco's) have bugs which cause call flow and registration failures. Some ALGs (including Cisco's) intermittently miss some packets, or in the case of fragmented packets, do not even examine and change headers.

When SIP-ALG is enabled, CP SBCs determine the endpoints are publicly addressed and therefore do not need frequent registration refreshes to keep the firewall port open between SBC and the endpoint. In this case, the firewall can close the port between Exitty and the device endpoint, causing an inability to receive incoming calls. The most common issues that result from enabled SIP-ALG when using Virtual Office applications include:

  • Outbound call status stuck in Dialing...
  • An inability to field incoming calls (call continues to ring and cannot be answered).
  • Phones not able to register with Exitty.

Additional SIP-ALG information and settings can be found at http://www.voip-info.org/wiki/view/Routers+SIP+ALG.

Device Guidance

It is highly recommended you have your network or IT administrator or a qualified professional configure the following in your router or firewall.

ALG settings are typically found in the administration interface of the router, but each router’s configuration setup will differ. Check the manufacturer’s documentation to understand where to find and disable this setting in your device. (Please note that many routers will re-enable ALG by default if the router is ever reset or powered off then back on.)

The following are general guidelines for popular makes and models. If you don't see your router or manufacturer below, consult the manufacturer's documentation.

Adtran Routers

Add the following:

no ip firewall alg sip

Arris Gateways 

  1. Go to Advanced > Options.
  2. Disable (uncheck) SIP.
  3. Click Apply.

Arris Gateway IP Address: 192.168.0.1

  • Username: admin
  • Password: motorola

ASA Routers

  1. Go to policy-map global_policy > class inspection_default.
  2. Enter:
no inspect sip

 Cisco (non-ASA)

On Cisco devices, SIP-ALG is referred to as SIP Fixup and is enabled by default on both routers and Pix devices. Because this is a default setting, no indication of it being "on" or "off" is visible in the configuration.

To disable SIP Fixup, issue the following commands:

General Routers

no ip nat service sip tcp port 5060
no ip nat service sip udp port 5060

Enterprise-Class Routers

no ip nat service sip tcp port 5060
no ip nat service sip udp port 5060

Pix Devices

no fixup protocol sip 5060
no fixup protocol sip udp 5060
  1. From the admin interface page of the router, navigate to Advanced settings.
  2. Under Application Level Gateway (ALG) Configuration, uncheck the SIP option.

Fortinet Routers

  1. From CLI interface, type the following commands:
  • config system session-helper 
  • show system session-helper

    (Look for the session instance that refers to SIP—likely to be #12)

  • Delete 12

    (Or number corresponding to SIP reference)

  1. To confirm deletion, run show system session-helper again.
  2. Ensure there is no reference to SIP or port 5060.

Linksys Routers

General Linksys Guidelines

  1. From the ADMIN page of the router, navigate to [Administration] > [Advanced].
  2. Look for and disable a SIP ALG option.

Linksys BEFSR41

  1. From the ADMIN page of the router, navigate to [APPLICATIONS & GAMING] > [PORT TRIGGERING].
  2. Enter [TCP] as the application.
  3. Enter [5060] into the Start Port and End Port for both the Triggering Range and Forwarded Range.
  4. Check Enable. 
  5. Save Settings.
  6. Reboot IP phone.

Netgear Routers

  1. From administration interface, go to Security > Firewall > Advanced settings.
  2. Uncheck the option for SIP ALG.
  3. Under Security > Firewall > Session Limit, increase the UDP timeout to the 300 seconds.

 SonicWall Routers

  1. Uncheck the box for Use SIP Header Transformation.
  2. Disable consistent NAT.

When setting the Global Default UDP timeout value on a SonicWall firewall, you must still fix the pre-existing rules' individual UDP timeout values. New rules will inherit the Global Default. Increase the UDP timeout to the suggested 300 seconds both globally on the firewall and the specific out-bound firewall rule (or the default rule, as the case may be).

UBEE Gateways

  1. Go to Advanced > Options.
  2. Disable (uncheck) SIP.
  3. Disable (uncheck) RTSP.
  4. Click Apply.

ZyXEL ZyWALL USG Routers

  1. Go to Settings > Configuration > Network > ALG.
  2. Disable SIP ALG.

    • Related Articles

    • Grandstream GXP1620 1625 IP Phone Quick User Guide

      Grandstream GXP 1620/1625 IP Phone Quick User Guide Basic Phone Operation USING THE HEADSET OR SPEAKER Use the Speaker Button to turn speaker ON/OFF. Use the Headset button to use the headset once it had been connected. MAKING A CALL Take ...

    • Grandstream GRP260X Essential IP Phone Quick User Guide

      Grandstream GRP260X Essential IP Phone Quick User Guide Basic Phone Operation USING THE HEADSET OR SPEAKER Use the Speaker Button to turn speaker ON/OFF. Use the Headset Button to use the headset once it had been connected. MAKING A CALL Take ...

    • Grandstream GRP2614/2615/2616 IP Phone Quick User Guide

      Grandstream GRP2614/2615/2616 IP Phone Quick User Guide Basic Phone Operation USING THE HEADSET OR SPEAKER Use the Speaker Button to turn speaker ON/OFF. Use the Headset button to use the headset once it had been connected. MAKING A CALL Take ...

    • Grandstream GXP2130/2140/2160/2135/2170 IP Phone Quick User Guide

      Grandstream GXP2130/2140/2160/2135/2170 IP Phone Quick User Guide Basic Phone Operation USING THE HEADSET OR SPEAKER Use the Speaker Button to turn speaker ON/OFF. Use the Headset button to use the headset once it had been connected. MAKING A CALL ...