Dynapath 10 (Data Line Option) Configuration Document
CNC Parameters
Machine Parameters:
Baud Rate = 4800
Data Bits = 7
Stop Bits = 1
FactoryWiz DNC Settings
Basic Communication
1.01- Port Type: Standard
1.11- Baud: 4800
1.12- Data Bits: 7
1.13- ASCII Even
1.14- Stop Bits: 1
1.15- Handshake: XON/XOFF
1.16- Handshake Send Signal: CTS
Sending Options
2.11- Leader:<10>
2.12- Trailer: END<13><10>
2.23- Skip lines that contain: END
2.31- Automatic timeout: 7
Receiving Options
3.11- Program identifier 1: (
3.12- Program Identifier 2:
3.21- Receive timeout: 3
3.31- Ignore data before first end-of-block: False
3.32- Ignore data after last end-of-block: False
Remote Commands
4.02- Request for file command:
4.03- Request for file command (drip feed):
4:11- Request to save command:
Additional Notes
Changing CNC Parameters:
Press MODE SELECT.
Type in R5, press ENTER (sets default baud rate to 4800)
Type in P1, press ENTER (sets default parity to EVEN)
Type in X1, press ENTER (sets XON/XOFF to ON)
Type in E0, press ENTER (sets default for ECHO to OFF)
Outputting CNC Programs:
Press MODE SELECT
Press 8 (RECORD OPTION)
Press ENTER
Press RECORD PROGRAM
Inputting CNC Programs:
Press MODE SELECT
Press 9 (LOAD OPTION)
Press ENTER
Press LOAD PROGRAM (Busy loading will be displayed)
Wiring Diagram:
Pinout includes RTS/CTS Handshaking
|
|
DB-9 com port |
Wire color |
DB-25 CNC |
Jumper? |
|
|
(Disconnected) |
Shield |
1 |
|
|
|
2 (Receive Data) |
Green |
2 (Transmit Data) |
|
|
|
3 (Transmit Data) |
Red |
3 (Receive Data) |
|
|
|
5 (Signal Ground) |
Black |
7 (Signal Ground) |
|
|
|
7 (RTS) |
Brown |
5 (CTS) |
|
|
|
8 (CTS) |
Blue |
4 (RTS) |
|
|
|
|
|
6 (DSR) 8 (DCD) 20 (DTR) |
JUMPER |
Related Articles
Yasnac I80 Configuration Document
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! Set the ...Fadal Configuration Document
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! CD,8 ...Cincinnati 900 Configuration Document
CNC Parameters Machine Parameters for Dataline: Marriage Parameter: 150 = 0 (NO PARITY) 151 = 10 (4800) 152 = 0 (1 stop bit) FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even ...Cincinnati 850 Configuration Document
CNC Parameters Machine Parameters for Dataline: Baud Rate = 4800 Parity = NONE Data Bits = 8 Stop Bits = 1 Protocol Level = 1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 8 1.13- ASCII None ...Cincinnati 850Sx Configuration Document
CNC Parameters Machine Parameters for Dataline: Baud Rate = 4800 Parity = NONE Data Bits = 8 Stop Bits = 1 Protocol Level = 1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 8 1.13- ASCII None ...