FTP Configuration for Fanuc Series CNC Machines

FTP - Fanuc 0i, 30i, 31i, 32i

Changing CNC Parameters

You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications!

Place the NC into MDI mode
Press the SETTING function key until the "SETTING (HANDY)" page is displayed.
Cursor down to I/O Channel.
I/O=9 (for FTP)

System (Param) screen:
System button
Press  > Screen button until Embedded appears.
Select Embedded
Select Common.  Enter the IP address for machine, Subnet Mask, and Router IP if necessary.

Select FTP Transfer.  Enter Host Name IP Address of PC/Server running the FactoryWiz Server software.  (This must be a static IP Address!).
Enter Port# 21
Enter Username: FTP
Enter Password: FACTORYWIZ
Page down.
Login Folder path:             (leave this field blank)
Select Restart to enable settings.
Host Select - Connect1
 

FactoryWiz DNC Settings

Basic Communication
1.01- Port Type: FTP_Server
1.03- IP Address of Fanuc control (This must be a static IP Address!)
1.21- End of block (EOB): LF
 
Sending Options:
2.11- Leader: %<10>
2.12- Trailer: %
2.23- Skip lines that contain: %
 
Receiving Options:

3.01- Use CNC defined filename only True/False - If True, it will save program same as program stored in CNC.
                                                                                   - If False, it will use 3.11/3.12 configurations
3.11- Program identifier 1: O
3.12- Program Identifier 2: :
3.21- Receive timeout: 3
3.31- Ignore data before first end-of-block: True
3.32- Ignore data after last end-of-block: True

 
Remote Commands:

4.02- Request for file command: GET-
4.03- Request for file command (drip feed): DNC-
4:11- Request to save command: PUT-
 
After adding a new FTP machine, you will need to Restart the FactoryWiz DNC Server Application/Service.
 

Additional Notes

If you have communications issue, make sure Firewall is turned off!!!!

Outputting CNC Programs

 To output a program, set the CNC to "EDIT" mode.
Press the PROG key on the control panel.
Display the program you wish to send on the screen by keying in the program number then pressing the down-arrow button.
Press the Operate (OPRT) softkey.
Use the right screen keys (in softkey row under LCD screen) until F Output appears.
Press F OUTPUT, Type in the program name, then press F SET.
Press EXEC.

 Inputting CNC Programs

 Queue file to be sent at FactoryWiz Clint workstation first, then at machine control:
Set the CNC to "EDIT" mode.
Press the PROG key on the control panel.
Press the Operate (OPRT) softkey.
Use the right screen keys (in softkey row under LCD screen) until F INPUT appears.
Press F INPUT, key in filename you would like, (a Queued file will ignore what is typed in, so you can call it anything, such as 0001.
Press EXEC.



    • Related Articles

    • FTP - Fanuc 0i Configuration Document

      CNC Parameters Setting (HANDY) screen: I/O=9 (for FTP) System (Param) screen: System button Press >Screen button until Embedded appears. Select Embedded Select Common. Enter the IP address for machine, Subnet Mask, and Router IP if necessary. Select ...
    • FTP - Fanuc 0i, 30i, 31i, 32i Configuration Document

      CNC Parameters Setting (HANDY) screen: I/O=9 (for FTP) System (Param) screen: System button Press >Screen button until Embedded appears. Select Embedded Select Common. Enter the IP address for machine, Subnet Mask, and Router IP if necessary. Select ...
    • Brother C00 FTP Configuration

      CNC Configuration Sheet for FTP – Brother C00 You will need to verify all parameters listed below that correspond to your CNC control. Document (Phone camera) original settings before making modifications! CNC Parameters: Press EDIT button. Press ...
    • Fanuc 0T Configuration Document

      CNC Parameters (Phone camera) original settings before making modifications! Setting screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) Parameters screen: 0002 = 1xxxxxx0 (do not change values for x) 0552 = 10 (4800 baud rate) 9=2400, ...
    • Fanuc 0M Configuration Document

      CNC Parameters (Phone camera) original settings before making modifications! Setting screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) Parameters screen: 0002 = 1xxxxxx0 (do not change values for x) 0552 = 10 (4800 baud rate) 9=2400, ...