How to Adjust 4 mA in IRD7100 reading Vibration in mm/sec RMS when Vibration is Zero (0)

IRD7100 is an Online Monitoring System. It is designed to continuously monitor vibration of a Machine and transmit its vibration to the Control Room. One popular way of transmitting the vibration information is by using 4-20 mA Output. Here, 4 mA indicates 0 Vibration and 20 mA indicates Full Scale Vibration. The steps in this article mention the procedure for setting 4 mA on IRD7100 in an event the observed mA is less or more than 4 mA when there is no vibration.

To carry the steps listed, you will need a Small Cable to make a Loop, a Fine Screw Driver with Flat head, A Multimeter with ability to read DC Current in mA and the IRD7100 Transmitter.

The steps listed with image are applicable to IRD7100 reading vibration in mm/sec RMS, but can also be used for other scaling and ranges with proper interpretation.

1. Step 1: Ensure that IRD7100 is powered on with the correct Power Input (230 V AC, 24 V DC, 110 V AC, whichever may be applicable)
   
2. Step 2: Using a Multimeter reading mA DC, measure the current across terminals 4 and 5 for Channel 1 and then Channel 2. Proceed to next step only if the value is not within +/-1% of 4.00 mA DC
   
3. Step 3: If the observed value is not within +/-1% of 4.00 mA DC, then you proceed for calibration of this value. To do so, Loop Terminals 1 and 2 for the Channel which you are adjusting/calibrating and proceed to Step 4
   
4. Step 4: Using a Fine Screw Driver with a Flat Head, make minute adjustments to Trimpot P2 on PCB M67124 if adjustments are being made to Channel 1 OR make minute adjustments to Trimpot P2A on PCB M67124 if adjustments are being made to Channel 2 (refer image for trimpot location). While adjusting, observe the mA DC on the multimeter.
   
5. Step 5: Stop making further adjustments when the mA DC reading comes between +/-1% of 4.00 mA DC. The calibration is done. Remove the Loop on Terminals 1 and 2, and proceed to use IRD7100 as normal.
   

For any help, please feel free to call us on +91-2248972000 or WhatsApp on +91-9167947195 or email us on service@irdmech.com

• Related Articles

• User Manual of Generator End Winding Vibration Monitoring System Card M88280 of IRD8800 Series

  Attached to this Article is the User Manual of Generator End Winding Vibration Monitoring System (GEWVMS) Card M88280 of IRD8800 Series

• IRD8800 MODBUS Output Register Map

  Attached you will find the MODBUS RTU/MODBUS TCP/IP Register Map for Cards of the Vibration Monitoring System IRD8800. This register map applied to all cards i.e M88200, M88210, M88250 and M88280

• Which Type Tests has IRD8800 passed?

  IRD8800 is our flagship Vibration Monitoring System and is API 670 Compliant. The series has been type tested for the following tests in which it has passed and the results are current: Dry Heat Cyclic, IS:9000 P-III Damp Heat Cyclic, IS: 9000 P-V ...

• How many copies of 4-20 mA output per channel in IRD7100 Machinery Protection Transmitter (MPT)?

  By default, IRD7100 MPT is equipped with 1 copy of 4-20 mA output per channel. However, in some cases where Customer requires 1 copy of 4-20 mA for connection to DCS/PLC/SCADA and 1 copy of MODBUS RTU Output from MPT - in such cases we provide 2 ...

• User Manual of IRD7100 - Machinery Protection Transmitter

  The User Manual for IRD7100 - Machinery Protection Transmitter is attached to this Article