IRD8800 - API 670 Compliant Vibration Monitoring System
Tx Fail Relay Contacts in IRD8800 Series Monitoring System
IRD8800 Series Monitoring System is designed to provide Tx Fail Relay Contacts per Module in the event of Transducer Failure (Sensor going bad or fault in cable). These contacts can be used for Annunciation. The TX Fail Relay operates when any ...
IRD8800 as replacement for IRD5915
IRD Mechanalysis had a Vibration Monitoring System called IRD5915 in the 20th Century. IRD5915 is now obsolete and is succeeded by our 21st Century Vibration Monitoring System IRD8800. Attached is a drawing which shows how IRD8800 can fit in a cut ...
Firmware Versions of IRD8800 Series Modules M88200, M88210, M88250, M88280, M88300 and M88950
The Firmware Versions in use for IRD8800 Series Modules as on the date of this article are: Module Type Microcontroller Make Firmware Version M88200 Cypress V-1.1.5, 1/10/10 M88200 Microchip V-1.1.7, 26/05/2016 M88210 Microchip V-1.1.0, 2/6/16 M88250 ...
IRD8800 Module M88300 Menu Structure
Attached to this article is the menu structure of Module M88300 of IRD8800 Series
Sensitivity Setting in IRD8800 module M88200
Module M88200 of IRD8800 series allows Sensitivity setting in mV/g and mV/mm/sec. When Sensitivity Unit is set to mV/g, then the card allows setting a sensitivity value between 000.0 and 999.9 mV/g. Typically, the factory set value is kept at 100.0 ...
Typical Backplane Connections for IRD8800
This article lists how connections can be made on Backplane Terminals for IRD8800 - various modules When using IRD8800 Module M88200 with Contact Type Vibration Sensor (IRD521 (Accelerometer) or IRD531 (Velometer), refer the drawing present at this ...
Sensitivity options in IRD8800 Module M88210
The Relative Shaft Vibration Module M88210 of IRD8800 Series allows different Sensitivity options to accommodate different Eddy Current Probes of different manufacturers keeping different Sensitivities. The option to minutely adjust sensitivity also ...
Pre-Commissioning Checklist for IRD8800 Generator End Winding Vibration Monitoring System (GEWVMS)/Stator End Winding Vibration Monitoring System (SEWVMS)
Before IRD8800 for Generator End Winding Vibration Monitoring can be commissioned, the following needs to be ensured by Purchaser at site: Sensors within the Generator (Turbine End and Exciter End) have been mounted and their output has been brought ...
User Manual of Generator End Winding Vibration Monitoring System Card M88280 of IRD8800 Series
Attached to this Article is the User Manual of Generator End Winding Vibration Monitoring System (GEWVMS) Card M88280 of IRD8800 Series
M88250 Recalibration Procedure
The below steps are for calibration in mm/sec pk for Module M88250. The same steps can be repeated by changing display units to mm/sec RMS or microns pk-pk or microns pk. Pre-Requisites Function Generator with Ability to generate Sine Wave (choose an ...
Sensitivity of M88280
M88280 Module of IRD8800 Series is meant for Vibration Monitoring of Generator End Winding. The sensitivity of the module can be adjusted based on the input high temperature sensor and Charge Amplifier. The Sensitivity for a Charge Amplifier with an ...
M88950 MODBUS Register Map
Communication Setting : Baud Rate=57600 (Settable), Parity=None (Settable), Data Bit=8, Stop Bit=1 Function 03 : Data Read , Function 06 : Data Write Sr. No. Parameters Function Register Numbers Values CH-1 CH-2 CH-3 CH-4 1 Relay Delay 03/06 0 1 2 3 ...
Calibration Check Table for IRD8800 Series Module M88210
Pre-requisites If you wish to check the Calibration of IRD8800 Series Module M88210, then you would need the following tools: A Signal Generator with the capability to generate a Sine Wave of a fixed frequency and fixed amplitude and an accuracy of ...
User Manual of M88200 of IRD8800 Series
The User Manual of Module M88200 of IRD8800 Series is attached to this article and can be printed or downloaded from here
Calibration Check Table for IRD8800 Series Module M88200
Pre-requisites If you wish to check the Calibration of IRD8800 Series Module M88200, then you would need the following tools: A Signal Generator with the capability to generate a Sine Wave of a fixed frequency and fixed amplitude and an accuracy of ...
User Manual of M88210 of IRD8800 Series
The User Manual of Module M88210 of IRD8800 Series can be downloaded and printed using the attachment to this article.
Which Type Tests has IRD8800 passed?
IRD8800 is our flagship Vibration Monitoring System and is API 670 Compliant. The series has been type tested for the following tests in which it has passed and the results are current: Dry Heat Cyclic, IS:9000 P-III Damp Heat Cyclic, IS: 9000 P-V ...
IRD8800 MODBUS Output Register Map
Attached you will find the MODBUS RTU/MODBUS TCP/IP Register Map for Cards of the Vibration Monitoring System IRD8800. This register map applied to all cards i.e M88200, M88210, M88250 and M88280
What is the purpose of key phasor module in vibration monitoring system? Can it be used to extract balancing data?
The purpose of the Key Phasor module in a Vibration Monitoring System is to act as the reference point for phase on a machine train. Using this reference point, the vibration phase of other sensors on the machine train can be deduced. Usually the ...